Model		LS-7001
Type		Standard
No. of connectable sensor heads		2 (fully compatible for all head types except monitor (M) models)
Display	Measurement display	Main display: 7-segment red LED (Character height: 20.3 mm 0.80″) Sub-display: 7-segment red LED (Character height: 9.9 mm 0.39″) x 3
	Minimum display unit	0.01 µm to 100 µm (7-level selectable)
	Display range	±99.99999 to ±9,999.9 mm ±3.937″ to ±393.7″ (Linked to minimum display unit setting, mm/µm selectable)
	Measurement position monitor	7-level display with a red LED
	Tolerance check output display	Green LED (GO), Red LED x 2 (HI, LO)

Model		LJ-X8000A
Head input		Up to 1 head Compatible with LJ-X8000 series heads and LJ-V7000 series heads
Sampling cycle (trigger interval)		When connecting the LJ-X8000 Series: maximum speed of 16 kHz (63 μs) When connecting the LJ-V7000 Series: maximum speed of 64 kHz (16 μs) (Luminance output types for model designations ending with B have a maximum speed of 8 kHz (125 μs))
Interface	Control input	Supports the batch measurement start (MEASURE_START) and batch measurement stop (MEASURE_STOP).
	Control output	•Supports the trigger ready (READY) and system error (ERROR). •Photo MOSFET
	Synchronous input / output	For trigger synchronization of multiple controllers
	Ethernet	Supports the profile output, setting, controll, 1000BASE-T/100BASE-TX

Model		LK-G3001
Type		Separate monitor model
Display	Head compatibility	All LK-G sensor heads are compatible
	Number of connectable sensors	Maximum of 2 units
	Minimum display unit	0.01 µm
	Display range	±9,999.99 mm to ±9,999.99 µm (Selectable from six levels)
	Refresh rate	10 times/sec
Terminal block	Analog voltage output	±10 V x 2 outputs, output impedance: 100 Ω
	Analog current output	4 to 20 mA x 2 outputs, maximum load resistance: 350 Ω
	Timing input	For OUT1, non-voltage input
	Reset input
	Auto-zero input
	Laser remote interlock input	Non-voltage input
	Comparator output	For OUT1, NPN open-collector output
	Alarm output	For OUT1, NPN open-collector output (N.C.)

Model		CL-3000
Type		Controller
Number of optical unit connections		Controller only: 2 units; using expansion units / relay units: 6 units
Interface	EtherNet/IP™	Supports cyclic communication and message communication; RPI: 1 to 10,000 ms (0.5 ms units) Maximum number of connections: 8, complies with Version CT14 conformance test Cannot be used when using PROFINET, PLC link or EtherCAT
	PROFINET	Compatible with conformance class A. Cannot be used when using EtherNet/IP™, PLC link or EtherCAT
	PLC-Link	The following PLCs are supported: Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series Cannot be used when using EtherNet/IP™, PROFINET or EtherCAT
	Ethernet	Allows for measurement data output and control I/O via no-protocol command communication with PCs and PLCs 100Base-TX, capable of communication with CL-NavigatorN
	USB	Conforms to USB 2.0 HighSpeed, capable of communication with CL-NavigatorN
	RS-232C	Allows for measurement data output and control I/O via no-protocol command communication with PCs and PLCs Baud rate: 9600 to 115,200 bps, data length: 8 bit, stop bit: 1 bit, parity: none / even numbers / odd numbers
	Terminal (IN)	13 (supports function switching via software)
	Terminal (OUT)	11 (supports function switching via software)

Productos